OCOntario Certification Registry

Fuel Industry Certificate Record

Gas Technician 2 (G.2) Certificate

The G.2 is the working licence of Ontario's residential gas trade. It covers natural gas and propane appliances up to 400,000 Btuh input, which includes almost every furnace, water heater and fireplace in a house.

Fast facts

CertificateGas Technician 2 (G.2), commonly searched as G2 gas licence, gas technician 2, G2 course or G2 exam
Fuel familyNatural gas and propane (vapour)
Issued byTechnical Standards and Safety Authority (TSSA)
Legal basisO. Reg. 215/01 (Fuel Industry Certificates), s. 3 (1); scope in s. 21
Exam pass mark75% (TSSA Gas/Oil Burner Technician certification policy, updated March 2025)
Exam fee$89 per attempt; $255.50 to challenge without training (from May 1, 2026, plus HST)
Certificate fee$136 initial and renewal (from May 1, 2026, plus HST)
RenewalEvery 2 years; $50 late payment fee after the renewal date
TransferableNo (O. Reg. 215/01, s. 17)

Last verified August 19, 2026 against the sources listed below.

What can a G2 holder legally do in Ontario?

A G.2 holder may install, inspect, alter, purge, activate, repair, service or remove a natural gas or propane appliance with an input of 400,000 Btuh or less, plus the equipment and accessories essential to its operation. In doing that work, the holder may:

  • Perform the same connected functions a G.1 holder may perform on piping, venting, water-piping reconnection, components and the gas side of air conditioning equipment, on appliances within the 400,000 Btuh limit
  • Work on appliances above 400,000 Btuh only under the direct supervision of a G.1 certificate holder

Boundaries of the G2

  • The 400,000 Btuh input ceiling is the boundary between the G.2 and the G.1 (O. Reg. 215/01, ss. 20-21)
  • Plumbing beyond appliance reconnection requires a plumber or steamfitter certificate of qualification; work beyond the gas side of a refrigeration or air conditioning unit requires a refrigeration and air conditioning systems mechanic

The full scope wording is in O. Reg. 215/01, s. 21, which prevails over any summary.

Is a certificate legally required for gas work?

Under O. Reg. 212/01 (Gaseous Fuels), s. 6 (1), no person may install, alter, purge, activate, repair, service or remove any appliance or equipment used in the handling or use of gas unless they hold a certificate for that purpose. The only exception is working in the physical presence of someone who holds the appropriate certificate.

The requirement is in O. Reg. 212/01, s. 6 (1). Working without the certificate is an offence under the Technical Standards and Safety Act, 2000.

How do you get the G2 in Ontario?

Prerequisite

You must already hold a G.3 certificate, or a valid certificate of qualification as an operating engineer under O. Reg. 219/01, when you apply (O. Reg. 215/01, s. 7). See the G3 Gas Technician 3 certificate requirements.

The training route

  1. Complete an approved program at an accredited training provider. Certification requires a TSSA-approved curriculum delivered by an accredited provider (O. Reg. 215/01, s. 5 (1)), with a 75% pass on each module and on the practical evaluations.
  2. Apply for the TSSA certification exam. Your provider submits proof of training; you book through the TSSA Client Portal. The practical assessment stays valid for 12 months after the program.
  3. Pass the TSSA certification exam with 75% or higher. Each attempt, including rewrites, is billed as a separate exam. Failing three times means completing a full accredited program before another attempt (O. Reg. 215/01, s. 5 (4)).
  4. Pay the certificate fee. $136 for the initial certificate (from May 1, 2026, plus HST), per the TSSA Natural Gas & Hydrogen Fee Schedule.

The challenge route

Experienced workers can challenge the exam without formal training if TSSA is satisfied they hold equivalent knowledge and competence (O. Reg. 215/01, s. 5 (5)). The challenge examination costs $255.50, requires documented proof of work experience where the certificate has prerequisites, and still ends in a practical skills assessment.

How often does the G2 need to be renewed?

Every two years. TSSA's fee schedules list the certificate fee as biennial, and the renewal costs $136 (from May 1, 2026, plus HST) with a $50 late payment fee after the renewal date. For the gas and oil burner classes, TSSA's certification policy anchors the expiry to the second anniversary of the holder's birthday after issue.

Working on an expired certificate is prohibited outright: O. Reg. 215/01, s. 4 (1) says a person who fails to renew shall not do any work under the certificate after expiry. You can still renew up to one year after expiry, completing any upgrading course the director specifies. After one year, the certificate is gone and you start over as a new applicant (s. 4 (5)).

Where the G2 sits in the ladder

After two years or 4,000 hours working as a G.2, including 500 hours on systems above 400,000 Btuh under G.1 supervision, you can apply for the G.1. Next step: G1 Gas Technician 1 certificate requirements.

Related certificates and trades

Official verification sources

How this record is built: scope, prerequisites and renewal law are read directly from O. Reg. 215/01 as consolidated on e-Laws; fees come from TSSA's published fee schedules and the pass mark from TSSA's certification policies. The page is assembled programmatically from those verified facts and reviewed before publishing. Facts not verified against a primary source are marked as not published rather than estimated.